cable | Moto-Abruzzo

01/06/201728/04/2019

John Walker (UK) – Power / Ground cable kit

Aprilia Caponord ETV1000 Rally-Raid John Walker power ground earth cable kit Ok, so with the old starter solenoid removed and a little starter-circuit modification simmering in the old mental stewing-pot, it was time to remove the OEM solenoid-starter cable, along with the Earth(Ground) cable and the battery-solenoid-30A-fuses cable and fit the new upgraded items from John Walker (UK).

Removing the ground and starter cable required the removal of the crash bars and side panels along with lowering the sump guard (remove front bolts and pivot on rear) to allow extra room to lower the oil tank and move the oil cooler – both to illicit a little more room to remove nuts/bolts more easily with the tools at hand. With the respective ends disconnected it was just a matter of a few tie-wraps to be removed and the old cables slid out of the frame. The battery-starter cable requires a bit more work (care?) as the two wires to the 30A fuses need to be cut. These will be spliced with the new ones on John’s loom, so I carefully pulled the black sleeving back as far as possible, matched the old/new looms together then cut the cables at what seemed the sensible place!

Now with all three cables clear of the bike I could lay them out and compare them to John’s replacements. Not only am I impressed by the workmanship of the new cables, but also that they are approximately 15mm longer than the old ones – not over the top and certainly not too short, just nice – a little extra flexibility when fitting. One thing I really like about John’s cables is the extra mounting point on the Positive and Negative lugs – very useful indeed.

After lunch, in they went with no drama at all. I spliced the 30A cables together with crimp/solder joints that are then sheathed with heatshrink. John doesn’t provide the splices, but he does supply the heatshrink! With that done, the old black sleeve can be wiggled back up into place and the whole thing then looks very ‘OME’! Running the cables down the frame is easy enough as they’re quite flexible – surprising as they’re almost (if not more!) than twice the diameter of the old cables …… this does make things a little tight getting the cables in place either side of the battery, but a bit of patience and a wiggle here and there gets them seated comfortably.

Before tie-wrapping everything and refitting panels and guards it just left the little matter of trying it out! So ignition on …. no pop, bang or fire (good start!) then thumb the starter button and ………….wow! What a difference, the engine spins like a hyperactive puppy spotting its tail for the first time – fantastic! Putting the multimeter on the battery (fully charged), then cranking the motor over showed a minimum voltage (momentary as the starter takes the in-rush current) of about 10.8V. That’s way better than it used to be. Steady cranking voltage rises back up to about 11.8V…….. and as mentioned cranking speed is very impressive now!

With that done, it was time to button the rest of the bike back together and try it all out on the road. What a difference a week makes eh? From ‘Dear dog please start, please start …. oh and starter please disengage, pppplease disengage’ to ‘Oi you, call that a starter? …… Listen in awe my wayward friend because THIS is a starter!’

In the end did I really need them? Well truthfully, no the originals are fine, no corrosion and the insulation is intact, but at the time of ordering I really didn’t know one way or the other. Yes I could have made my own, but sometimes like having a meal served to you rather than cooking yourself, it’s nice to buy in the finished item ready to fit. Besides, I just wanted upgraded replacements not some fancy parts made from gold wire finer than badger bum-fluff with diamond encrusted unobtanium connections! In the end I’m glad I did buy them ….. the starting is much more energetic now and that’s worth its weight in gold right there!

So if you are in any doubt at all about your wiring, then drop John a line and I’m sure you will also be as pleased as I am with the results. Price including postage in the UK (May 2017) is £70.00GBP

26/09/201526/09/2015

MCCruise control revisited

While the Caponord was stripped for the vacuum check-valve replacement, I decided to get my act in gear and finally, once and for all, unequivocally ….. Sort out the MCCruise control/throttle cables. Last year I relocated the CIU (Cable Interface Unit) to the left hand side of the throttle body. This had pros and cons ……….. The upside was a lighter feel on the throttle grip, the downside, the Servo/CIU and CIU/Throttle body cables were overly long and the Servo cable fed into the CIU from the wrong side. However, the cruise was working perfectly and so it became one of those ‘mañana’ jobs!

Well today is that tomorrow! First I jotted down a list of what had to be done:

1. Make a spacer to fit onto the side of the CIU. This is to move the throttle cable adjuster further out and make the inner cable a better fit on the spool.
2. Drill new cable holes in the CIU so it can be rotated 180° so the Servo cable enters from the rear not the front as is the current arrangement.
3. Shorten the CIU/Throttle cable while allowing for the new spacer at the CIU – 350mm down to 190mm.
4. Shorten the 1,150mm Servo cable to a more reasonable 750mm!

I have to say here and now that I do like learning new skills or adapting old ones to suit a new task. I also have to admit that in a good few years on this Earth, I’ve never made up or adjusted the length of clutch/choke/throttle cables before! So time to adapt the electronics soldering skills and brush up on required technique courtesy of the Internet. Now I’m not going to bore you to tears telling you how to do it – there is tons of advice on various websites/YouTube. Suffice to say, sort out the duff advice from the good, have the right equipment to hand and practice, practice, practice …… do the job once and do it right! All the cable bits and pieces I needed came from Venhill in the UK.

By late afternoon everything was buttoned up and the cruise control recalibrated after the throttle bodies were rebalanced, fault codes cleared and TPS reset via TuneECU. As the sun faded behind the hills I cracked open a cold beer happy with how the day played out …. Time then to put the tools away and get back to revising for the next Amateur Radio Exam!

The MCCruise has been installed for approx. 25,000 miles and worked perfectly throughout. The CIU was relocated because the initial location proved to be problematic – causing slight binding of the throttle cable. This meant that the cables supplied in the kit (as specified by me) were now the wrong length and the orientation of cable entry into the CIU was wrong.This is not the fault of MCCruise, what they sent is what I asked for! Should anyone else wish to go down this route I will of course be glad to provide notes/measurements etc so a kit will be a simple bolt-on job.

18/01/201524/01/2015

Stuff …. 6 months and 12 months on

A couple of anniversaries this week ….. firstly the dashboard. Yes a full 12 months since it was finished and put back into the Capo for the last time, resplendent with its new inlay to complement the electronic changes. The auto-dimming back lighting and split indicator repeaters have been absolute winners – I couldn’t go back to a standard board again without missing them. Moving the side-stand and low-fuel lights to Aprilia Caponord ETV1000 & Rally-Raid Voltmeter and re-located side-stand light on dashboard accommodate the twin indicator repeaters has had no impact, positive or negative. The voltmeter has been a different kettle of fish …. generally unused as the Sparkbight battery monitor handles voltage feedback when riding around – however it has proved a real benefit during start-up when the dashboard goes through its self-test phase. Now it’s become second nature to eye-ball the tacho needle to see what the battery voltage is pre-start. >12.6v and I know I should get a good kick from the battery!

Aprilia Caponord ETV1000 & Rally-Raid MCCruise control The second anniversary, although shorter at 6 months and a tad over 11K miles, is the MCCruise cruise control. After a rushed install (not clever) I knew I had a heavier throttle than pre-installation ….. this was purely down to throttle cable routing and nothing to do with the cruise control itself. It simply didn’t like being re-routed behind the radiator, so I gave up and relocated the CIU (cable interface unit) to a new location by the throttle bodies. Now everything works fine – a light throttle and a happy cruise control. It’s been 100% reliable and functional. As a demonstration of its finesse I ran the bike in 1st gear at 25mph and let the cruise control take over the (100 horsepower!) throttle – all I can say is WOW! I would never have believed that the system could have the sensitivity to operate the throttle with such precision, but it did – up hill, down dale – never an ounce of jerkiness. Ok I admit no one wants to ride around in 1st gear …. but as an experiment, it proved to me that MCCruise have indeed developed an absolutely fantastic piece of kit.